Description
Vehicle Compatibility
This product is designed to fit the following vehicles:
- Mazda BT50 4×4 Dual Cab (3rd generation “TF” June 2020 onward)
- Isuzu DMax 4×4 Dual Cab (3rd generation “RD” October 2019 onward)
- Nissan Navara 4×4 Dual Cab (3rd Generation “NP300” with ISOFIX rear child seat anchor points only)
- Mercedes X-Class 4×4 Dual Cab
Battery Compatibility
This product has been designed to mount super-slim lithium batteries from Australia’s favourite battery manufacturers.
Maximum battery case size:
- Height = 300mm
- Length = 690mm
- Thickness = 65mm
Batteries that are knows to fit are listed here in manufacturer alphabetical order:
Amptron
- 100Ah Lithium Blade Battery AT-LFP-12-100HV01
Baintech
- BTLP12V110-100SL
- BTLITH-1275-SL
- BTLITH -1275-SL-DCS
- BTLITH -12110-SL
- BTLITH -12110-SL-DCS
Custom Lithium
- 100Ah Super-slim lithium – Plastic and metal case versions, all terminal types.
Deep Cycle Systems (DCS)
- DCS Super Slim Line Lithium DCS-12V-100AH-SL
Dingo Box
- DingoBox 105Ah slim lithium
iTechworld
Whilst this product will allow installation of the iTech100SS, a dedicated bracket is now available – Click here for details
Installation Notes – BT50 and DMax
The installer must use a drill to increase the size of one hole in a bracket on the back wall of the cab (see photo). An M6 thread insert (supplied with the battery mount) must then be fitted to that hole using a simple, cost effective tool available from tool shops and large hardware stores. This product cannot be fitted without the supplied thread insert being added to the vehicle.
The plastic trim panel that is fitted to the back wall of the cab and the other down the side of the back wall will need to be trimmed a little during installation.
Installation Notes – Navara and X-Class
Suitable for all NP300 Navara vehicles, including those with the electric rear sliding window. Early vehicles without ISOFIX rear seat anchors require thread inserts or M10 bolts (not included) to be fitted in the vehicle floor to secure the battery mount.
For vehicles with the electric sliding rear window, the actuator is relocated to above the battery. It’s proven to work well in this new location but the installer will need to extend the wiring to the actuator (a basic two wire cable).
Requires no drilling or cutting of metalwork to install this product in vehicles with ISOFIX rear seat anchors.
Installation Notes – All Vehicles
Installation takes approximately one hour.
Includes pre-cut holes for Redarc BCDC charger, multiple midi fuse holders, Victron shunt.
Carpet on back wall of the cab must be removed to install this product. You may decide to trim the carpet panel and fit the remains on either side of the battery mount but most owners opt to leave the carpet panel out of the vehicle.
Frequently Asked Questions
Do I need to drill any holes or cut the cab carpet?
BT50 and DMax owners will need to increase the size of one existing hole as shown above. The bracket bolts directly into existing factory mounting points on the cab back wall and floor. The carpet panel will need to be trimmed around the back plate.
Which side of the cab is the battery mounted on?
The battery is positioned on the right-hand (driver’s) side behind the rear seat backrest. This keeps the battery secure in the cab recess and leaves the passenger side clear for mounting your other electrical gear.
Will the rear seat latch back into its standard position?
Yes. The bracket is specifically profiled around the rear seat folding mechanism, allowing the rear seat backrest to latch securely into the factory locks without obstruction.
Can I mount my fuses and battery monitor shunt directly to this bracket?
Yes. The bracket includes pre-cut mounting locations for twin MIDI fuse holders (fuses facing outward for easy access) and dedicated mounting points for an iTechworld Shunt.
What is the largest capacity battery that will fit?
The battery size is limited by the dimensions of the case; Height = 300mm, Length = 690mm. Thickness = 65mm
This size battery case touches the seat back along the top edge and the height is limited by the upper mounting position of the battery clamp. There’s just not enough space to fit a larger battery case.
Can I fit a 200Ah battery?
No – A 200Ah battery case is too big for this product.
Material
- Stainless Steel
- Injection Moulded Plastic
